View DNT12S0A0R05PFA_7564052.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

- datasheet ds_dnt12sip05_03292013 features ? high efficiency: 92% @ 12vin, 5v/5a out ? small size and low profile: 0.80? x 0.45? x 0.27? (smd) 0.90? x 0.40? x 0.25? (sip) ? standard footprint and pinout ? resistor-based trim ? output voltage programmable from 0.75vdc to 5.0vdc via external resistors ? pre-bias startup ? no minimum load required ? fixed frequency operation ? input uvlo, ocp ? remote on/off ? iso 9001, tl 9000, iso 14001, qs9000, ohsas18001 certified manufacturing facility ? ul/cul 60950-1 (us & canada) recognized, ? applications ? telecom/datacom ? distributed power architectures ? servers and workstations ? lan/wan applications ? data processing applications options ? negative on/off logic ? smd package delphi series dnt12 non-isolated point of load dc/dc power modules: 8.3~14vin, 0.75~5.0vo, 5a the delphi series dnt12, 8.3v~14v input, 5a single output, non-isolated point of load dc/dc converters are the latest offering from a world leader in power systems technology and manufacturing ? delta electronics, inc. the dnt12, 5a series provides a programmable output voltage from 0.75v to 5v using external resistors. this product family is available in a surface mount or sip package and provides up to 5a of current in an industry standard footprint and pinout. with creative design technology and optimization of component placement, these converters possess outstanding electrical and thermal performance and extremely high reliability under highly stressful operating conditions. the dnt12, 5a sip modules have excellent thermal performance and can provide full output current with little air flow.
ds_dnt12sip05_03292013 2 technical specifications (t a = 25c, airflow rate = 300 lfm, v in = 8.3vdc and 14vdc, nominal vout unless otherwise noted.) parameter notes and conditions dnt12s0a0r05nfa min. typ. max. units absolute maximum ratings input voltage 0 15 vdc operating temperature -40 85 c storage temperature -55 125 c input characteristics operating input voltage 8.3 12 14 v input under-voltage lockout turn-on voltage threshold 7.95 v turn-off voltage threshold 7.80 v maximum input current vin=vin,min to vin,max, io=io,max 3.5 a no-load input current vo=5v 50 70 ma off converter input current 1 10 ma inrush transient vin= vin,min to vin,max, io=io,min to io,max 0.4 a 2 s recommended input fuse tbd a output characteristics output voltage set point vin=12v, io=io,max -1.5 vo,set +1.5 % vo,set output voltage adjustable range 0.7525 5.0 v output voltage regulation over line vin=vin,min to vin,max 0.4 % vo,set over load io=io,min to io,max 0.4 % vo,set over temperature 0.4 % vo,set total output voltage range over sample load, line and temperature -3.0 +3.0 % vo,set output voltage ripple and noise 5hz to 20mhz bandwidth peak-to-peak vin=min to max, io=min to max1f ceramic, 10f tan 40 70 mv rms vin=min to max, io=min to max1f ceramic, 10f tan 20 25 mv output current range 0 5 a output voltage over-shoot at start-up 5 % vo,set output dc current-limit inception 160 % io output short-circuit current (hiccup mode) io,s/c 1.5 adc (rms) dynamic characteristics dynamic load response 47f tan & 1f ceramic load cap, 5a/s positive step change in output current 50% io, max to 100% io, max 150 mvpk negative step change in output current 100% io, max to 50% io, max 150 mvpk setting time to 10% of peak deviation 25 s turn-on transient io=io.max start-up time, from on/off control von/off, vo=10% of vo,set 15 25 ms start-up time, from input vin=vin,min, vo=10% of vo,set 15 25 ms maximum output startup capacitive load full load; esr ? 1m ? 1000 f full load; esr ? 10m ? 3000 f efficiency vo=0.75v vin=12v, io=io,max 71.0 % vo=1.2v vin=12v, io=io,max 79.0 % vo=1.5v vin=12v, io=io,max 82.0 % vo=1.8v vin=12v, io=io,max 84.0 % vo=2.5v vin=12v, io=io,max 87.0 % vo=3.3v vin=12v, io=io,max 89.5 % vo=5.0v vin=12v, io=io,max 92.0 % feature characteristics switching frequency 480 khz on/off control, (negative logic) logic low voltage module on, von/off -0.2 0.3 v logic high voltage module off, von/off 2.5 vin,max v logic low current module on, ion/off 10 ua logic high current module off, ion/off 0.2 1 ma general specifications mtbf io=io,max, ta=25 j 1 m hours weight 2.1 grams
ds_dnt12sip05_03292013 3 electrical characteristics curves figure 1: converter efficiency vs. output current (12v in, 5v output voltage) figure 2: converter efficiency vs. output current (12v in, 3.3v output voltage) figure 3: converter efficiency vs. output current (12v in, 2.5v output voltage) figure 4: converter efficiency vs. output current (12v in, 1.8v output voltage) figure 5: converter efficiency vs. output current (12v in, 1.5v output voltage) figure 6: converter efficiency vs. output current (12v in, 1.2v output voltage)
ds_dnt12sip05_03292013 4 electrical characteristics curves figure 7: output ripple & noise at 12vin, 1.2v5a out 20mv/div, pk-pk : 12.50mv, rms : 2.79mv(20mv/div,2us/div) figure 8: output ripple & noise at 12vin, 2.5v/5a out 50mv/ div , pk-pk :17.50mv, rms :4.67mv(20mv/div,2us/div) figure 9: output ripple & noise at 12vin, 3.3v/5a out 50mv/div, pk-pk :20.00mv, rms :5.59mv(20mv/div,2us/div) figure 10: output ripple & noise at 12vin, 5.0v/5a out pk-pk :24.16mv, rms :7.36mv ( 20mv/div,2us/div) figure 11: turn on delay time at 12vin, 5.0v5a out (10ms/div) top trace :vout , 2v/ div ; bottom trace :vin ,20v/div figure 12: turn on delay time at remote on/off, 5.0v/5 a out (10ms/div).top trace: vout ,2v/div ;bottom trace :on/off , 5v/div.
ds_dnt12sip05_03292013 5 electrical characteristics curves figure 13: turn on using input on/off with external capacitors (co=3000 f), 5.0v/5a out (resistive load)(10ms/div) top trace:vout, 2v/div; bottom trace: vin ,20v/div figure 14: turn on using remote on/off with external capacitors (co= 3000 f), 5.0v/5a out (resistive load)(10ms/div) top trace: vout,2v/div; bottom trace: on/off,5v/div figure 15: typical transient response to step load change at 5a/ s from 100% to 50% of io, max at 12vin, 5.0v out (cout = 1uf ceramic+ 47 f ceramic)(100mv/div, 20us/div) figure 16: typical transient response to step load change at 2.5a/ s from 50% to 100% of io, max at 12vin, 5.0v out (cout = 1uf ceramic+ 10 f ceramic)(100mv/div, 20us/div) figure 17: output short circuit current 12vin, 0.75vout (0.5v/div,50ms/div) figure 18: turn on with prebias 12vin, 5v/0a out, vbias =3.3vdc . (5ms/div) top trace : vout,5v/div; bottom trace: vin, 10v/div
ds_dnt12sip05_03292013 6 test configurations v i (+) v i (-) battery 2 100uf tantalum l to oscilloscope note: input reflected-ripple current is measured with a simulated source inductance. current is measured at the input of the module. figure 19: input reflected-ripple test setup vo gnd copper strip 10uf tantalum 1uf ceramic scope resistive load note: use a 10 f tantalum and 1 f capacitor. scope measurement should be made using a bnc connector. figure 20: peak-peak output noise and startup transient measurement test setup supply i vi vo gnd io load contact and distribution losses contact resistance figure 21: output voltage and efficiency measurement test setup note: all measurements are taken at the module terminals. when the m odule is not soldered (via socket), place kelvin connections at module terminals to avoid measurement errors due to contact resistance. % 100 ) ( = i i vi io vo design considerations input source impedance the power module should be connected to a low ac-impedance input source. highly inductive source impedances can affect the stability of the module. an input capacitance must be placed close to the modules input pins to filter ripple current and ensure module stability in the presence of inductive traces that supply the input voltage to the module. safety considerations for safety-agency approval the power module must be installed in compliance with the spacing and separation requirements of the end-use safety agency standards. for the converter output to be considered meeting the requirements of safety extra-low voltage (selv), the input must meet selv requirements. the power module has extra-low voltage (elv) outputs when all inputs are elv. the input to these units is to be provided with a adequate time-delay fuse in the ungrounded lead.
ds_dnt12sip05_03292013 7 design considerations (con.) remote on/off the dnt series power modules have an on/off pin for remote on/off operation. both positive and negative on/off logic options are available in the dnt series power modules. for positive logic module, connect an open collector (npn) transistor or open drain (n channel) mosfet between the on/off pin and the gnd pin (see figure 22). positive logic on/off signal turns the module on during the logic high and turns the module off during the logic low. when the positive on/off function is not used, leave the pin floating or tie to vin (module will be on). for negative logic module, the on/off pin is pulled high with an external pull-up resistor (see figure 23) negative logic on/off signal turns the module off during logic high and turns the module on during logic low. if the negative on/off function is not used, leave the pin floating or tie to gnd. (module will be on) rl vo vin on/off gnd i on/off figure 22: positive remote on/off implementation vo vin on/off gnd rpull-up rl i on/off figure 23: negative remote on/off implementation over-current protection to provide protection in an output over load fault condition, the unit is equipped with internal over-current protection. when the over-current protection is triggered, the unit enters hiccup mode. the units operate normally once the fault condition is removed. features descriptions output voltage programming the output voltage of the dnt can be programmed to any voltage between 0.75vdc and 5.0vdc by connecting one resistor (shown as rtrim in figure 24) between the trim and gnd pins of the module. without this external resistor, the output voltage of the module is 0.7525 vdc. to calculate the value of the resistor rtrim for a particular output voltage vo, please use the following equation: rtrim 10500 vo 0.7525 ? 1000 ? ? ? ? ? ? ? ? := rtrim is the external resistor in ? vo is the desired output voltage
ds_dnt12sip05_03292013 8 features descriptions (con.) for example, to program the output voltage of the dnt module to 3.3vdc, rtrim is calculated as follows: rtrim 10500 2.5475 1000 ? ? ? ? ? ? ? ? := rtrim = 3.122 k ? dnt can also be programmed by applying a voltage between the trim and gnd pins (figure 25). the following equation can be used to determine the value of vtrim needed for a desired output voltage vo: vtrim 0.7 vo 0.7525 ? ( ) 0.0667 ? ? ? ? ? ? := vtrim is the external voltage in v vo is the desired output voltage for example, to program the output voltage of a dnt module to 3.3 vdc, vtrim is calculated as follows vtrim 0.7 2.5475 0.0667 ? ( ) ? := vtrim = 0.530v figure 24: circuit configuration for programming output voltage using an external resistor figure 25: circuit configuration for programming output voltage using external voltage source table 1 provides rtrim values required for some common output voltages, while table 2 provides value of external voltage source, vtrim, for the same common output voltages. by using a 1% tolerance trim resistor, set point tolerance of 2% can be achieved as specified in the electrical specification. table 1 vo (v) rtrim (k ? ) 0.7525 open 1.2 22.464 1.5 13.047 1.8 9.024 2.5 5.009 3.3 3.122 5.0 1.472 table 2 vo (v) vtrim (v) 0.7525 open 1.2 0.670 1.5 0.650 1.8 0.630 2.5 0.583 3.3 0.530 5.0 0.4167 the amount of power delivered by the module is the voltage at the output terminals multiplied by the output current. when using the trim feature, the output voltage of the module can be increased, which at the same output current would increase the power output of the module. care should be taken to ensure that the maximum output power of the module must not exceed the maximum rated power ( vo.set x io.max p max ).
ds_dnt12sip05_03292013 9 thermal considerations thermal management is an important part of the system design. to ensure proper, reliable operation, sufficient cooling of the power module is needed over the entire temperature range of the module. convection cooling is usually the dominant mode of heat transfer. hence, the choice of equipment to characterize the thermal performance of the power module is a wind tunnel. thermal testing setup delta?s dc/dc power modules are characterized in heated vertical wind tunnels that simulate the thermal environments encountered in most electronics equipment. this type of equipment commonly uses vertically mounted circuit cards in cabinet racks in which the power modules are mounted. the following figure shows the wind tunnel characterization setup. the power module is mounted on a test pwb and is vertically positioned within the wind tunnel. the height of this fan duct is constantly kept at 25.4mm (1??). thermal derating heat can be removed by increasing airflow over the module. to enhance system reliability, the power module should always be operated below the maximum operating temperature. if the temperature exceeds the maximum module temperature, reliability of the unit may be affected. air flow modu le pw b 50.8(2.00") air velocity a nd am bi e nt temperature sured below the module fan cing pw b note: wind tunnel test setup figure dimensions are in millimeters and (inches) figure 27: wind tunnel test setup feature descriptions (con. ) voltage margining output voltage margining can be implemented in the dnt modules by connecting a resistor, r margin-up , from the trim pin to the ground pin for margining-up the output voltage and by connecting a resistor, r margin-down , from the trim pin to the output pin for margining-down. figure 26 shows the circuit configuration for output voltage margining. if unused, leave the trim pin unconnected. a calculation tool is available from the evaluation procedure, which computes the values of r margin-up and r margin-down for a specific output voltage and margin percentage. vo on/off vin gnd trim q2 q1 rmargin-up rmargin-down rtrim figure 26: circuit configuration for output voltage margining
ds_dnt12sip05_03292013 10 thermal curves figure 28: temperature measurement location the allowed maximum hot spot temperature is defined at 125 j . dnt12s0a0r05(standard) output current vs. ambient temperature and air velocity @vin =12v,vo=5.0v (either orientation,preliminary curves) 0.0 1.0 2.0 3.0 4.0 5.0 25 30 35 40 45 50 55 60 65 70 75 80 85 natural convection ambient temperature ( j ) output current (a) 300lfm 400lfm 200lfm 100lfm 500lfm 600lfm figure 29: output current vs. ambient temperature and air velocity@ vin=12v, vo=5.0v (either orientation, preliminary curves) dnt12s0a0r05(standard) output current vs. ambient temperature and air velocity @vin =12v,vo=3.3v (either orientation,preliminary curves) 0.0 1.0 2.0 3.0 4.0 5.0 25 30 35 40 45 50 55 60 65 70 75 80 85 natural convection ambient temperature ( j ) output current (a) 400lfm 300lfm 200lfm 100lfm 600lfm 500lfm figure 30: output current vs. ambient temperature and air velocity@ vin=12v, vo=3.3v (either orientation, preliminary curves) dnt12s0a0r05(standard) output current vs. ambient temperature and air velocity @vin =12v,vo=2.0v (either orientation,preliminary curves) 0.0 1.0 2.0 3.0 4.0 5.0 25 30 35 40 45 50 55 60 65 70 75 80 85 natural convection ambient temperature ( j ) output current (a) 400lfm 300lfm 100lfm 500lfm 200lfm figure 31: output current vs. ambient temperature and air velocity@ vin=12v, vo=2.0v (either orientation, preliminary curves) dnt12s0a0r05(standard) output current vs. ambient temperature and air velocity @vin =12v,vo=0.75~1.5v (either orientation,preliminary curves) 0.0 1.0 2.0 3.0 4.0 5.0 25 30 35 40 45 50 55 60 65 70 75 80 85 natural convection ambient temperature ( j ) output current (a) 300lfm 200lfm 400lfm 100lfm figure 32: output current vs. ambient temperature and air velocity@ vin=12v, vo=0.75~1.5v (either orientation, preliminary curves)
ds_dnt12sip05_03292013 11 pick and place location surface- mount tape & reel lead (sn/pb) process recommend temp. profile time ( sec. ) pre-heat temp. 140~180 x c 60~120 sec. peak temp. 210~230 x c 5sec. ramp-up temp. 0.5~3.0 x c /sec. temperature ( x c ) 50 100 150 200 250 300 60 0 120 180 240 2nd ramp-up temp. 1.0~3.0 x c /sec. over 200 x c 40~50sec. cooling down rate <3 x c /sec. lead free (sac) process recommend temp. profile temp . time 150 j 200 j 90~120 sec. time limited 75 sec. above 220 j 220 j preheat time ramp up max. 3 j /sec. ramp down max. 4 j /sec. peak temp. 240 ~ 245 j 25 j note: all temperature refers to assembly application board, measured on the land of assembly application board.
ds_dnt12sip05_03292013 12 mechanical drawing smd package (optional) sip package note: all pins are copper alloy with matte tin(pb free) plated over nickel under-plating.
ds_dnt12sip05_03292013 13 part numbering system dnt 12 s 0a0 r 05 n f a product series input voltage numbers of outputs output voltage package type output current on/off logic option code dnt ? 3a or 5a 04 - 2.4v ~ 5.5v 12 - 8.3v ~ 14v s - single 0a0 - programmable r - sip s - smd 05 - 5a n- negative p- positive f- rohs 6/6 (lead free) a - standard functions model list model name package input voltage output voltage output current efficiency 12vin, 5vout full load dnt12s0a0s03nfa smd 8.3v ~ 14vdc 0.75v ~ 5.0vdc 3a 93.5% dnt12s0a0r03nfa sip 8.3v ~ 14vdc 0.75v ~ 5.0vdc 3a 93.5% dnt12s0a0s05nfa smd 8.3v ~ 14vdc 0.75v ~ 5.0vdc 5a 92% dnt12s0a0r05nfa sip 8.3v ~ 14vdc 0.75v ~ 5.0vdc 5a 92% dnt12s0a0r05pf a sip 8.3v ~ 14vdc 0.75v ~ 5.0vdc 5a 92% contact: www.deltaww.com/dcdc usa: telephone: east coast: 978-656-3993 west coast: 510-668-5100 fax: (978) 656 3964 email: dcdc@delta-corp.com europe: phone: +31 (0)20 655 09 67 fax: +31 (0)20 655 09 99 email: dcdc@delta-es.com asia & the rest of world: telephone: +886 3 4526107 ext 6220 fax: +886 3 4513485 email: dcdc@delta.com.tw warranty delta offers a two (2) year limited warranty. complete warranty information is listed on our web site or is available upon request from delta. information furnished by delta is believed to be accurate and reliable. however, no responsibility is assumed by delta for its use, nor for any infringements of patents or other rights of third parties, which may result from its use. no license is granted by implication or otherwise under

▲Up To Search▲

Price & Availability of DNT12S0A0R05PFA

	To Download DNT12S0A0R05PFA Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .